Role of Mo and Zr Additions in Enhancing the Behavior of New Ti-Mo Alloys for Implant Materials
Awad, Ahmed H.; Saood, Modar; Aly, Hayam A.; Abdelghany, Ahmed W. (2024-10-21)
Awad, Ahmed H.
Saood, Modar
Aly, Hayam A.
Abdelghany, Ahmed W.
Springer
21.10.2024
Awad, A.H., Saood, M., Aly, H.A. et al. Role of Mo and Zr Additions in Enhancing the Behavior of New Ti–Mo Alloys for Implant Materials. Met. Mater. Int. 31, 1232–1253 (2025). https://doi.org/10.1007/s12540-024-01813-7
https://creativecommons.org/licenses/by/4.0/
© The Author(s) 2024. This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
https://creativecommons.org/licenses/by/4.0/
© The Author(s) 2024. This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
https://creativecommons.org/licenses/by/4.0/
Julkaisun pysyvä osoite on
https://urn.fi/URN:NBN:fi:oulu-202410286486
https://urn.fi/URN:NBN:fi:oulu-202410286486
Tiivistelmä
Abstract
The utilization of Ti–Mo alloys in biomedical applications has gained attention for use in biomedical applications owing to their non-toxicity, reasonable cost, and favorable properties. In the present study, Ti–12Mo–6Zr and Ti–15Mo–6Zr alloys were prepared using elemental blend and mechanical alloying techniques. The effect of alloying elements Mo and Zr of Ti–Mo alloy, as well as the effect of fabrication techniques of Ti–Mo–Zr trinary alloys, were investigated. Thermodynamic calculations supported by CALPHAD analysis revealed that the addition of Zr increases lattice distortion, which contributes to enhancing the strength. Conversely, adding Mo decreases the enthalpy, facilitating improved mixing and solid solution formation. The as-sintered samples were characterized by X-ray diffraction, optical microscope, and scanning electron microscopy, and their microhardness, compressive, and corrosion behavior were investigated. Among all the investigated alloys, Ti–15Mo–6Zr alloy prepared by the mechanical alloying technique, milled for six hours at 300 rpm, compacted at 600 MPa, and sintered at 1250 ℃, shows good comprehensive mechanical properties with a preferable compressive strength (− 1710 MPa) and hardness (396 HV5), as well as the lowest wear rate (0.69%) and corrosion rate (0.557 × 10–3 mm/year). This can be related to the solid solution strengthening and relative density, together with dispersion and precipitation strengthening of the α phase. Remarkably, the combination of high mechanical and corrosion properties can be achieved by tailoring the content of the α phase, controlling the density, and providing new fabricating techniques for β Ti alloys.
The utilization of Ti–Mo alloys in biomedical applications has gained attention for use in biomedical applications owing to their non-toxicity, reasonable cost, and favorable properties. In the present study, Ti–12Mo–6Zr and Ti–15Mo–6Zr alloys were prepared using elemental blend and mechanical alloying techniques. The effect of alloying elements Mo and Zr of Ti–Mo alloy, as well as the effect of fabrication techniques of Ti–Mo–Zr trinary alloys, were investigated. Thermodynamic calculations supported by CALPHAD analysis revealed that the addition of Zr increases lattice distortion, which contributes to enhancing the strength. Conversely, adding Mo decreases the enthalpy, facilitating improved mixing and solid solution formation. The as-sintered samples were characterized by X-ray diffraction, optical microscope, and scanning electron microscopy, and their microhardness, compressive, and corrosion behavior were investigated. Among all the investigated alloys, Ti–15Mo–6Zr alloy prepared by the mechanical alloying technique, milled for six hours at 300 rpm, compacted at 600 MPa, and sintered at 1250 ℃, shows good comprehensive mechanical properties with a preferable compressive strength (− 1710 MPa) and hardness (396 HV5), as well as the lowest wear rate (0.69%) and corrosion rate (0.557 × 10–3 mm/year). This can be related to the solid solution strengthening and relative density, together with dispersion and precipitation strengthening of the α phase. Remarkably, the combination of high mechanical and corrosion properties can be achieved by tailoring the content of the α phase, controlling the density, and providing new fabricating techniques for β Ti alloys.
Kokoelmat
- Avoin saatavuus [38840]